Audi A4, S4
- Introduction
About this Management
Cars Audi A4/S4 - the summary
Identification numbers of the car
Acquisition of spare parts
Technology of service, the tool and the workplace equipment
Поддомкрачивание and towage
Start of the engine from the auxiliary storage battery
Automobile химикалии, oils and greasings
Diagnostics of malfunctions
+ Controls and receptions of safe operation
+ Current leaving and service
+ The engine
+ Systems of cooling, heating and the air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual box of a gear change
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Diagnostics of malfunctions The description of diagnostics of electronic control systems and diagnostic codes are resulted in the Head of System of an electric equipment of the engine. In the given Section the most simple scheme of finding-out of the reasons of malfunctions and the refusals occurring in knots and systems of a vehicle is offered. Refusals and their possible reasons are broken into groups on the basis of the relation to certain components or car systems as, for example the engine, cooling system, etc., besides, in the text are given the references concerning given problems. Remember that successful end of search of causes of defect at all is not the black magic accessible to only skilled professional mechanics, and is defined by a combination of certain knowledge and the patient, regular approach to problem research. To move always follows from simple to difficult, to lead up each check to the logic end, and to try not to pass the obvious facts - everyone can forget to fill fuel in a fuel tank or to leave for the night included lighting devices. And at last, always it is necessary to try to make an accurate picture of development of malfunction and to undertake corresponding steps on relapse prevention. If refusal of an electric equipment was the result of infringement of quality of contact, check up at the same time a condition of all other contacts and electric sockets of system. If the same safety lock some times continues to fuse successively, there is no sense in its further replacement - it is necessary to try to find out a cause of a failure. Remember that failure of a minor component can be a sign of infringement of functioning of more important knot or the whole system. The engine
If the engine is not started, it is necessary to analyse a situation. That the petrol engine in general could be started, two basic conditions should be satisfied. In cylinders the mix should arrive fuel-air, and on a spark plug the spark should be developed. Therefore, first, it is necessary to check up, whether fuel moves. Address to the Head of the Power supply system, release and decrease in toxicity of the fulfilled gases. To define, whether the spark is developed, it is necessary to turn out candles, to insert into tips and separately to put to weight. Thus a tip or a cable of ignition do not hold hands, and use well isolated nippers. Ask the assistant to start the engine. If the spark is absent, address to the Head of System of an electric equipment of the engine. Procedures of diagnostics of an electronic control system and codes of malfunctions are resulted in the Head of System of an electric equipment of the engine.
Engine start
All engines
-
РКПП: Tighten a lay brake, completely squeeze out a pedal of coupling and hold it. A check point establish in neutral position. The switched off coupling facilitates engine start, especially at low external temperatures since thus there is no friction from outside a check point. -
Automatic transmission: Establish the selector in position «Р» or «N». Press a pedal of a brake and hold it.
|
Do not include a starter more than 30 with continuous, the starter and cables otherwise overheat. |
The petrol engine
- Turn the ignition key and include a starter, without giving thus gas. As soon as the engine will earn, release a key. If during 5 about the engine it is not started, press a pedal of gas a little and again repeat start. If the engine is not started or at once stops, repeat start with half squeezed out pedal of gas and if start with completely squeezed out pedal of gas is required still. At the hot engine a pedal of gas during start slowly squeeze out.
- Necessarily at once begin movement, only at a strong frost allow to the engine to get warm during 30 with.
|
Unsuccessful attempts of start of the engine following one after another can harm каталитическому to the converter since not burnt down gasoline gets to it and at heating blows up. |
The diesel engine
-
On the cold engine: Include ignition and wait when the control lamp of preheat will go out. At once after the control lamp has gone out, start the engine, without giving thus some gas. If at start there are irregular flashes, include a starter until then (a maximum 20) while the engine will not start to work independently. If all the same the engine is not started, turn the ignition key in position «0» and wait approximately 30 with. After that once again warm up the engine and repeat start as it is described above.
|
While preheat is made, it is not necessary to include powerful electric consumers, otherwise the storage battery without need is overloaded. |
|
The diesel engine with direct injection, as a rule, demands preheat application only at temperature more low 0°С. |
If the fuel tank has been completely emptied, process of start after refuelling lasts longer (to 1 mines) since air from fuel system thus leaves. -
On the warm engine preheat is not required. Start the engine at once, without giving some gas.
The engine is not turned at start attempts
- Corrosion of plugs of the battery or ослабло fastening on them of tips of wires takes place. Check up a condition of plugs and tips. Tighten клеммные clips, if necessary remove corrosion traces.
- The battery is discharged or faulty. If tips of wires are found pure and reliably fixed on battery plugs, turn the ignition key in position ON, then include headlights and-or windscreen cleaners. If the given electric equipment does not function, the battery is discharged.
- Transmission it is inexact it is established in position “Р”.
- Conducting in a chain of system of start or ослабло fastening of wires on plugs is torn off. Check up a condition of wires, plugs and electric sockets of the battery, the traction relay of a starter and the ignition lock.
- The starter gear wheel is jammed in a gear wreath drive a disk. Try to turn the engine for a pulley коленвала. At the first possibility remove a starter and check up a condition of a gear wheel and a gear wreath.
- The traction relay of a starter (the Head of System of an electric equipment of the engine) is faulty.
- The starter (the Head of System of an electric equipment of the engine) is faulty.
- The ignition lock is faulty.
The engine is turned, but not started
- Start is incorrectly made (Address to the materials presented above).
- It is faulty or is not disconnected иммобилизатор the engine.
- The safety lock is faulty:
- The electric fuel pump;
- Electronic system of injection.
- Concerning check of safety locks address to the Head the Onboard electric equipment.
- Empty fuel tank or poor-quality fuel is filled in.
- The air filter is strongly polluted. Vacuum leaks in elements of giving of air, malfunction in a control system of injection of fuel and ignition take place.
- The battery (the engine is turned too slowly) is discharged. Check up electric equipment functioning (address to the previous Section).
- Корродированы клеммные connections of the battery or ослабло their fastening (address to the previous Section).
- The fuel pump is faulty, has fused its safety lock or the pump relay is damaged. Check up on hearing noise of work of the pump at ignition inclusion (the Head of the Power supply system, release and decrease in toxicity of the fulfilled gases).
- Components of system of ignition (the Head of System of an electric equipment of the engine) are damaged or excessively humidified.
- Spark plugs are worn out or faulty or the candle backlash (the Head of System of an electric equipment of the engine) is incorrectly exposed.
- Conducting of an electric contour of system of start or ослабло fastening of wires on plugs (address to the previous Section) is torn off or disconnected.
- Conducting of a contour of the coil of ignition or ослабло fastening of wires on coil plugs (the Head of System of an electric equipment of the engine) is torn off or disconnected.
- The safety lock of the block of engine management is damaged, is faulty any of gauges: the Hall, the pulse gauge, the gauge of temperature of a cooling liquid or soaked up air (the Head of System of an electric equipment of the engine).
- Too low pressure of a compression. Replace a sealing lining of a head of cylinders. If necessary repair the engine.
The diesel engine
- Start is incorrectly made.
- It is faulty иммобилизатор the engine.
- The safety lock is faulty:
- The electric fuel pump;
- Preheat systems.
- The engine is not heated-up: проверьтеисправность functioning of the device of preheat.
- On electromagnetic запорном the valve there is no pressure. Connect to the switch the voltmeter or a sampler on a light-emitting diode. Include ignition. The light-emitting diode should light up. Otherwise it is necessary to find breakage of electroconducting and to eliminate it.
- It is faulty electromagnetic запорный the valve. Check up reliability of fastening of the electromagnetic switch, check up contacts. Switch on and off ignition. In the switch click should be distributed.
- Damage to a line of giving of fuel or air to lines takes place:
- Pipelines or hoses are mechanically damaged or littered. Clear fuel pipelines and remove air from lines and the filter.
- The fuel filter is littered. Replace filtering element.
- In the winter it is necessary to check up the filter and pipelines on ice or wax presence. Put the car in heated garage, add in gasoline system.
- Ventilation of a tank or the mesh filter топливозаборника is littered. Clean.
- Adjustment of the beginning of giving of fuel is brought down. Check up, make updating.
- Atomizers are faulty. Check up. Turn on consistently накидные nuts - at отворачивании nuts of the faulty cylinder engine turns will not fall.
- The fuel pump of a high pressure (ТНВД) is faulty. Establish for check new, or obviously serviceable ТНВД.
- Too low pressure of a compression. Replace a sealing lining of a head of cylinders. If necessary repair the engine.
The starter functions without проворачивания the engine
Start of the cold engine is complicated
Start of the hot engine is complicated
Starter gearing occurs is too noisy or with difficulty
- Teeth of a gear wheel of a starter or flywheel wreath are worn out or damaged.
- Bolts of fastening of a starter or ослабло effort of their tightening are lost.
The engine is started, but immediately глохнет
- It is faulty иммобилизатор the engine.
- Electroconducting or ослабло fastening of wires on coil or generator plugs is faulty.
- Malfunction a power supply system or electric equipment component (Heads of the Power supply system, release and decrease in toxicity of the fulfilled gases and System of an electric equipment of the engine) takes place.
- Base installations of the block of electronic control (ЕСМ) are broken.
- Damage to system of release/kataliticheskom the converter.
- Depression losses through прокладочные surfaces of the inlet pipeline or the block of injection of fuel take place. Make sure of reliability of an inhaling of fixing bolts/nuts, check up the fact and quality of fastening on the unions on the inlet pipeline of all vacuum hoses. Check up a condition of hoses and correctness of their connection (to the unions).
Stability of work of the engine on single turns is broken
- Leaks in an inlet air path take place. Make sure of reliability of an inhaling of fixing bolts/nuts, check up the fact and quality of fastening on the unions on the inlet pipeline of all vacuum hoses. Hear to the working engine by means of a stethoscope or a piece of a fuel hose. Presence of a hissing sound will allow to reveal a source of "leak" of vacuum. Not less effectively it is possible to take advantage for check by a solution of soap water.
- Malfunction a power supply system or electric equipment component (Heads of the Power supply system, release and decrease in toxicity of the fulfilled gases and System of an electric equipment of the engine) takes place.
- Serviceability of activation of an injector and the control of duration of injection is broken.
- Leaks through injectors/infringements of a stream of dispersion of fuel take place at injection.
- It is faulty докаталитический a ljambda-probe 1.
- Ignition low voltage.
- The valve of system of operated ventilation картера (the Head the Engine) is blocked.
- It is jammed, or supposes leaks valve EGR.
- The air filter (the Head of the Power supply system, release and decrease in toxicity of the fulfilled gases) is blocked.
- The fuel pump does not provide giving of enough of fuel to injectors of system of injection (the Head of the Power supply system, release and decrease in toxicity of the fulfilled gases).
- Leaks through a lining of a head of cylinders take place. Make measurement компрессионного pressure in engine cylinders.
- Camshaft cams (the Head the Engine) are worn out.
The diesel engine
- Quality of connections of fuel hoses on ТНВД and the fuel filter is broken. Replace fuel hoses, fix their collars, tighten screws of angular connections.
- It is mechanically damaged or ослабло fastening ТНВД. Check up fastening.
- Are mixed by junctions of the returnable pipeline and the pipeline of giving of fuel. Connections put on the places. The screw of connection of the returnable pipeline has marks “OUT”.
- Damage to a line of giving of fuel takes place:
- Pipelines or hoses are mechanically damaged or littered. Clear fuel pipelines.
- The fuel filter is littered. Replace filtering element.
- In the winter it is necessary to check up the filter and pipelines on ice or wax presence. Put the car in heated garage, add in gasoline system.
- Ventilation of a tank or the mesh filter топливозаборника is littered. Clean.
- Adjustment of the beginning of giving of fuel is brought down. Check up, make updating.
- Atomizers are faulty. Check up. Turn on consistently накидные nuts - at отворачивании nuts of the faulty cylinder engine turns will not fall.
- The fuel pump of a high pressure (ТНВД) is faulty. Establish for check new, or obviously serviceable ТНВД.
Ignition admissions take place at engine work on single turns
Ignition admissions take place at car movement on transfer
The engine глохнет
The engine does not develop a total power
In addition for the diesel engine
- The air cleaner is littered. Clean or replace.
- Non-uniform giving of fuel ТНВД on cylinders. Adjust on the heated-up engine.
- The moment of the beginning of giving of fuel ТНВД is incorrectly established. Establish.
- The fuel filter or ТНВД (atomizer) is littered. Wash out the preliminary filter, replace an element of the filter of thin clearing, clean a spray or replace the pump (atomizer).
- Adjustment of the maximum frequency of rotation of a cranked shaft is broken.
There are claps in system of an admission or shots in release system
At movement with acceleration or uphill there are detonation sounds
Takes place калильное ignition (the engine continues to work after ignition deenergizing)
The diesel engine smokes
-
Black smoke:
- The air cleaner is polluted. Wash out and fill with fresh oil or replace an element.
- Inappropriate fuel is applied. Wash out a tank and replace fuel.
- The moment of the beginning of giving ТНВД is incorrectly established.
-
Dark blue smoke:
- Oil burning in the chamber of combustion owing to deterioration of piston rings, high level of oil in an air cleaner, deterioration of epiploons in covers турбокомпрессора, formations of thinnesses in a lining between the block-karterom and турбокомпрессором. Repair the engine, establish normal level of oil, replace epiploons, tighten fastening bolts турбокомпрессора or replace a lining.
- Fuel to one of atomizers does not move. Check up on heating of final branch pipes of a collector.
- Bad dispersion of fuel by an atomizer because of malfunction of the valve or spray breakage. Grind in the valve or replace an atomizer.
-
White or brown smoke:
- Low temperature in cooling system. Check up the thermostat.
- Bad work of atomizers owing to deterioration or spray breakage. Replace a spray.
Engine electric equipment
Procedures of diagnostics of an electronic control system and codes of malfunctions are resulted in the Head of System of an electric equipment of the engine.
The battery "does not hold" a charge
The control lamp of gymnastics does not die away at increase in turns
- It is weakened приводной a belt. Check up натяжитель клинового a belt.
- Damage обгонной муфты. Remove the generator and turn a generator power shaft to the left. If the working surface of a pulley does not rotate, damage, as a rule, in обгонной муфте.
- Damage of a regulator of pressure/generator. Disconnect a wire (D +) from an underside of the generator and include ignition. If now the control lamp does not light up, malfunction, as a rule, in a regulator of pressure or in the generator.
- Deterioration of brushes. Visually check up brushes, if necessary replace.
- Wire damage between the generator and a pressure regulator.
- Damage of the block of the panel of devices.
The control lamp of gymnastics does not light up at ignition inclusion
The control lamp of gymnastics burns after ignition deenergizing
- Diodes are punched. Check up diodes, replace диодную a payment.
Starter
If the starter does not turn, at first it is necessary to check up, that on the plug 50 traction relays were necessary pressure a minimum 10 V.Esli pressure below this value, it is necessary to check up the wires entering into a contour of a current of a starter under the scheme. Whether works a starter at full pressure of the battery, it is possible to check up as follows. - Not including transfers, include ignition.
- Close plugs 30 and 50 starters a wire of section a minimum 4 мм2, address also to materials of the Head of System of an electric equipment of the engine. If the starter works faultlessly, it is necessary to search for a cause of defect in wires to a starter. If the starter does not earn, it should be checked up in the removed condition.
Check condition: In places of connection of a wire should be well fixed and should not be oxidised.
The starter does not rotate at inclusion of the lock of ignition
- The battery is discharged. Charge the battery.
- Close plugs 30 and 50 starters: If the starter rotates - breakage of a wire 50 to the ignition lock takes place, the starter switch is faulty. Eliminate breakage, replace defective details.
- Breakage of a cable or weight socket, the battery it is discharged. Check up cables and battery sockets, measure pressure of the battery, if necessary charge.
- Insufficient passage of a current owing to the weakened or oxidised sockets. Clear tips of wires and the battery plug, check up connections between the battery, a starter and weight.
- There is no pressure on the plug 50 traction relays. Wire breakage, the starter switch is faulty.
The starter rotates slowly and does not turn коленвал
- The battery category. Charge the battery.
- Summer oil is filled in. Fill in all-weather oil.
- Insufficient passage of a current owing to the weakened or oxidised sockets. Clear poles and battery plugs, check up connections between the battery, a starter and weight.
- Coal brushes do not adjoin to a collector, заедают in directing, are worn out, broken, made oily or polluted. Check up brushes, clear or replace. Check up the directing.
- Insufficient distance between brushes and a collector. Replace brushes and clear directing brushes.
- The collector in grooves or has scorched and was made oily. Process a collector or replace an anchor.
- There is no pressure on the plug 50 (minute 8). Check up the switch of a starter or the traction relay.
- The bearing is broken. Check up the bearing, if necessary replace.
- The traction relay is faulty. Replace the traction relay.
The starter seizes and rotates the engine jerky
- The gear wheel drive is faulty. Replace a gear wheel drive.
- The gear wheel is polluted. Clear a gear wheel.
- The gear wreath of a flywheel is faulty. Process a gear wreath if it is required, replace a flywheel.
The starter gear wheel does not depart from a wreath
- The drive of a gear wheel or carving are polluted or damaged. Clear or replace a gear wheel drive.
- The traction relay is faulty. Replace the traction relay.
- The returnable spring ослабла or was broke off. Replace a returnable spring.
The starter continues to work after отпускания the ignition key
- The traction relay заело, is not disconnected. At once switch off ignition, replace the traction relay.
- The ignition lock is not disconnected. At once disconnect the battery, replace the ignition lock.
Electronic control system
The cold engine does not enter into a warming up mode
- The gauge of temperature of cooling liquid ECT is faulty.
- The measuring instrument of weight of air MAF is faulty.
- Leaks in an inlet air path take place.
The heated-up engine does not leave a warming up mode, or the fuel expense is raised
- It is faulty докаталитический a ljambda-probe 1.
- The valve of management is jammed by an adsorber purge in open position.
The engine pulls
- The measuring instrument of weight of air MAF is faulty.
- Ignition low voltage; it is faulty докаталитический a ljambda-probe 1.
The electronic control system of an acceleration (ЕА) has passed in emergency operation
- The rating value potentiometer in the gauge of position of a pedal is faulty.
- The potentiometer of an actuation mechanism of electronic control by an acceleration/tempostata/system of stabilisation of turns of idling (ЕА/СС/ISC) is faulty.
The power supply system
The fuel expense is excessive
The diesel engine
- Contamination of the returnable pipeline. Blow air the returnable pipeline from ТНВД to a fuel tank.
- Too high turns of idling and the maximum turns. Adjust.
- The engine has mechanical damages. Check up a compression, if necessary repair the engine.
Leaks of fuel take place and-or there is a gasoline smell
The engine is not started
- At starter inclusion the electric fuel pump does not work (is not audible noise from work). Slightly knock on the pump case to release заевшую a detail. Check up, whether pressure is put to the pump. Check up serviceability of a safety lock. Check up electric contacts on good conductivity.
- The relay of the fuel pump is faulty. Check up the relay.
- Giving of a food from ECM is broken; the system of authorisation of the driver (DAS) is faulty.
- Залипли valves of injectors. Check up injectors, if necessary replace. Check up pressure giving on injectors. For this purpose расстыкуйте a socket of injectors. Attach диодную a control lamp to a wire and include a starter. The control lamp should blink.
- Ignition low voltage. There is no signal from the gauge of ignition of the Hall or the gauge of temperature of a cooling liquid. Check up electric wires. Poll memory of malfunctions.
- Are damaged, littered or негерметичны fuel pipelines, there are defects of hoses.
- The fuel filter is littered.
- Негерметична inlet system. Подсасывается additional air.
- Are damaged or негерметичны vacuum pipelines.
- The pressure regulator is damaged. Check up residual pressure.
- The gauge of position throttle заслонки is damaged.
- There is no food of the block of electronic control by the engine.
- Ice or wax presence in the filter or pipelines of the diesel engine.
- Ventilation of a fuel tank is hammered, the filter in a tank is littered.
- Preheat of the diesel engine does not work or is not up to the end made.
- The valve отсечки fuel of the diesel engine is damaged.
- The moment of the beginning of giving of fuel is brought down.
- Atomizers of the diesel engine are damaged. Turn on by turns накидные nuts and check up, whether the corresponding cylinder works.
- It is faulty ТНВД.
- The compression owing to excessive increase in pressure of oil is broken.
The cold engine is started badly, works unstably
- Leaks in an inlet air path take place.
- Ignition low voltage.
- The gauge of temperature of cooling liquid ECT is faulty. Check up the gauge.
- The measuring instrument of weight of air MAF is faulty.
- Serviceability of activation of an injector and the control of duration of injection is broken.
- The maintenance WITH does not correspond to requirements. Check up the maintenance WITH and idling.
- Pressure of fuel does not correspond to demanded value. Check up pressure of fuel.
The warm engine is started badly, works unstably
- Leaks in an inlet air path take place. Check up inlet system. For this purpose leave the engine to idle and cover places of consolidations and connection on an inlet path with gasoline. If the number of turns increases by short time, eliminate not tight places.
|
Gasoline steams are poisonous, do not inhale them. |
- Serviceability of activation of an injector and the control of duration of injection is broken.
- The return valve of the fuel pump is damaged.
- Leaks in fuel system.
- Fuel elevated pressure in the power supply system.
- Malfunction of system of catching of steams of fuel.
- It is hammered or crumpled returnable топливопровод to a tank.
The engine works with faults
- Electric connections to the fuel pump interrupt from time to time. Check up a condition штекерных connections and sockets of electric wires of the fuel pump, a measuring instrument of a stream of air and the relay of the fuel pump. Check up a safety lock and places of contacts on the relay of the fuel pump. Clear contacts, if necessary replace.
- Poor quality of fuel, formation of steam stoppers. Fill qualitative fuel.
- Too low volume of giving of fuel. Check up productivity of the pump.
- The fuel filter is faulty. Replace the fuel filter.
- The fuel pump is faulty. Check up the fuel pump.
- Injectors are faulty. Check up injectors.
- The ljambda-probe is faulty, infringements in a chain of quality management of a mix or there is no heating of a ljambda-probe.
- The gauge of positions throttle заслонки is faulty. Check up the gauge of positions throttle заслонки.
- The final collector or reception pipe of system of release (there are leaks of exhaust gases) is damaged.
- Ослабло fastening of fuel hoses to ТНВД and to the fuel filter of the diesel engine.
- At connection are mixed by places submitting and returnable pipelines TNVD.
The engine works with faults on transitive modes and an idling mode
- Негерметична system of an admission of air. Check up connections of inlet system. Start the engine and grease with gasoline of a place of contact and connection in a soaking up path. If engine turns quickly increase, eliminate негерметичность.
- Idling adjustment is incorrect. Check up an idling regulator, the gauge of positions throttle заслонки, ljambda-adjustment.
- The gauge of full loading is faulty or incorrectly adjusted. Check up the gauge throttle заслонки.
The hot engine is not started
- Incorrect adjustment of the maintenance WITH. Check up the maintenance WITH and idling.
- Too a high pressure in fuel system. Check up pressure of fuel, if necessary replace a pressure regulator.
- The returnable pipeline between a regulator of pressure and a fuel tank is littered or will drive. Clean or replace the pipeline.
- The gauge of temperature of the engine is faulty. Check up the temperature gauge.
- Негерметична the power supply system. Make visual survey of all connections in the field of the engine and the electric fuel pump. Tighten all connections.
- Негерметична system of an admission of air. Check up all connections of inlet system.
The engine works after deenergizing
- Негерметичны injectors. Check up injectors.
- On the diesel engine the valve отсечки fuel does not work.
Greasing system
The control lamp does not burn after ignition inclusion
- The gauge of pressure of oil is faulty. Include ignition, disconnect a wire from the gauge of pressure of oil and close on weight. If the lamp lights up, replace the gauge.
- On the gauge pressure, contacts корродированы does not move. Check up electric wires and contacts.
- The control lamp is faulty. Replace a control lamp.
- The management block is faulty. Replace the management block.
The control lamp does not die away after engine start
- Oil перегрето. Fur-trees the control lamp dies away after gas giving, to do it is required nothing.
The control lamp does not die away after giving of gas or lights up during movement
- Pressure of oil too low. Check up oil level, if necessary add. Check up pressure of oil.
- The wire to the gauge of pressure of oil has short circuit on weight. Disconnect a cable from the gauge and take aside (without closing on weight), include ignition. If the lamp lights up, check up a wire.
- The gauge of pressure of oil is faulty. Replace the gauge.
Too low pressure of oil upon all turns
- In the engine there is not enough oil. Add oil.
- The mesh filter is littered. Remove the pallet картера, clear the mesh filter.
- The oil pump is worn out. Remove the oil pump and check up it, if necessary replace.
- Damages of bearings. Remove the engine.
Too low pressure of oil upon small turns
- The reduktsionnyj valve залип abroach because of pollution. Remove and check up the valve.
Too an oil high pressure at number of turns above 2000 rpm
- The reduktsionnyj valve does not open because of pollution. Remove and check up the valve.
Cooling system
Overheat
Overcooling
External leaks of a liquid
Internal leaks of a liquid
|
Internal leaks of a liquid usually come to light by check of a condition of impellent oil. Examine an edge measuring probeа and internal surfaces of a cover (covers) of cylinders on presence of traces of water and oil foaming. |
- Leaks through a lining of a head of cylinders take place. Make check of system of cooling by pressure.
- There are cracks on a mirror of cylinders or in head moulding. For check disassemble the engine (the Head the Engine).
There are liquid losses
- In system it is filled too much liquid (the Head of System of cooling, heating and the air conditioner).
- The liquid boils away as a result of an engine overheat.
- Internal or external leaks of a liquid take place.
- The radiator cover is faulty. Check up a cover pressure.
Liquid circulation is broken
Heater
The heater fan does not work
- The safety lock of the motor of the fan is faulty. Check up a fan safety lock, if necessary replace.
- The fan switch is faulty. Check up, whether pressure is put to preresistors, remove and check up the fan switch.
- The electromotor is faulty. Check up, whether pressure is put to contacts of the motor of the fan at the included ignition and the closed switch of the fan. If pressure is put, replace the motor.
The heater fan does not work on one of steps
- The preresistor is faulty. Replace a connection payment.
The heater is not switched off by a regulator
- The switch is faulty. Check up the switch.
- Cables adjusting mixing заслонки are damaged or badly mobile. Replace cables.
Too low capacity of heating
- Too low level of a cooling liquid. Check up level of a cooling liquid, if necessary add.
- The block of management of a heater has a heavy course, is faulty. Check up the block of management of a heater, if necessary replace a cable.
Noise in the field of the heater fan
- The dirt, leaves has got. Remove the fan and clean it, clear the air channel.
- Disbalance крыльчатки, malfunction of the bearing. Remove the fan motor, check up ease of a course.
Automatic transmission (АТ)
In view of complexity of design АТ diagnostics of its malfunctions and repair is desirable for spending a component in a workshop of car-care centre or representation branch of the company.
The shared problems connected with functioning of the mechanism of switching
- It is possible to carry the following to number of the refusals connected with infringement of adjustment of draught of switching:
- Engine start is possible at the positions of transmission which are distinct from “Р” (Parking) and “N” (Neutral).
- Indications of the indicator of position of transmission differ from really chosen transfer.
- The car moves at the transmission established in position “Р” or “N”.
- Transfers are switched hardly or any way.
Make adjustment of draught of a gear change (the Head Automatic transmission).
Transmission revolves, is switched hardly, publishes extraneous noise or does not provide car movement at installation on one of lobbies or a reverse gear
- There is a set of the possible reasons of the problems listed in heading, however under the competence of the mechanic-fan one of them - wrong level трансмиссионной liquids gets only.
- Before driving away the car in a car-care centre workshop check up level and a condition трансмиссионной liquids (the Head Current leaving and service). Modify level according to requirements of Specifications or replace a liquid together with the filter. If a situation was not corrected, address for the help to experts.
Leaks трансмиссионной liquids take place
- Liquid АТ has dark red colour. Traces of its leaks should not be confused to traces of impellent oil which can be taken down on картер transmissions by a running stream of air.
- For revealing and localisation of a source of leak first of all remove from a transmission boat all traces of a dirt and greasing. Take advantage approaching обезжиривателем and-or make steam cleaning. Then make on the car a short trip on small speed (that leak traces did not communicate a running stream far from its source). Stop, поддомкратьте the car and by visual survey establish a leak source. More often as those act:
-
The pallet картера transmissions: Tighten fixing bolts and-or replace a pallet lining.
-
Tube of a gulf of a liquid: Replace rubber consolidation in a place of an input of a tube in картер transmissions.
-
Lines трансмиссионной liquids: Tighten штуцерные connections or replace lines.
-
Ventilating tube: Transmission is overflowed and-or water has got to it.
Oil has brown colour or smells as ashes
Mode Kickdown does not join by full pressing a pedal (the hill-climbing gear does not join)
The engine is not started at any position of the selector or started in any position except Р and R
Transmission revolves, jerks or noise at a gear change. The car does not move at inclusion of modes D or R
Bridges
Extraneous noise
- Usual road noise. To updating do not give in.
- Noise of tyres. Check up a condition of protectors and pressure of a rating of tyres.
- Bearings of wheels, or ослабло effort of their tightening are worn out or damaged.
Vibrations
- 1 Check up a condition of bearings of wheels, serially поддомкрачивая corresponding from corners of the car and rotating a wheel manually. Listen thus to sounds starting with the bearing. Remove bearings and check up their condition.
Oil leaks
Brake system
|
Before coming to the definitive conclusion about presence of problems with brake system make sure that tyres are in a satisfactory condition and are pumped up with demanded pressure, adjustment of corners of installation переднихколёс is not broken and the car is not loaded in the non-uniform image. |
The increased course of a pedal of a brake
- The brake contour has failed. Check up, whether the brake liquid follows.
The brake pedal springs and fails
- Air in brake system. Remove air from system.
- There is not enough liquid in the tank. Add a new brake liquid, remove from system air.
- Formation of vials of steam. It is shown, mainly, at the big loading on brakes. Replace a brake liquid, remove air from system.
Decrease in effect of braking, pedal fails
- Негерметичность the pipeline. Tighten connections of the pipeline or replace tubes.
- Damage of cuffs to the main thing or working brake cylinders. Replace a cuff. In the main brake cylinder replace internal elements, if necessary replace the main cylinder.
- The rubber lining is damaged. Repair a support.
Bad braking, despite the big effort of pressing of a pedal
- Brake overlays are made oily. Replace brake Pads.
- Are established improper or hardened Pads. Replace Pads. Address to section «Acquisition of spare parts».
- The brake amplifier is faulty. Check up the brake amplifier.
- Are worn out brake Pads. Replace brake Pads.
At braking the car withdraws aside
- Pressure in tyres does not correspond to the demanded. Check up and modify pressure in tyres.
- Non-uniform deterioration of tyres. Replace the worn out tyres.
- Brake Pads are made oily. Replace Pads.
- On one axis are established different brake Pads. Replace Pads. Address to section «Acquisition of spare parts».
- Bad condition brake колодок. Replace Pads.
- Mines of supports are polluted. Clear directing and landing surfaces колодок in a support.
- Corrosion of cylinders of brake supports. Replace a support.
- Non-uniform deterioration brake Pads. Replace brake Pads (on both wheels).
Spontaneous braking
- The compensatory aperture in the main brake cylinder is littered. Clean the main cylinder and replace internal elements.
- Too small backlash between приводным a rod and the piston of the main brake cylinder. Check up a backlash.
Brakes heat up during movement
- The compensatory aperture in the main brake cylinder is littered. Clear the main cylinder and replace internal elements.
- Too small backlash between приводным a rod and the piston of the main brake cylinder. Check up a backlash.
- It is littered дросселирующее an aperture in the special valve on the bottom. Clear the main brake cylinder, replace internal elements and a brake liquid.
Brakes shiver
- Are established Pads inadequate type. Replace Pads. Address to section Acquisition of spare parts.
- Brake disk in places корродирован. Carefully grind a brake disk.
- The brake disk has lateral palpation. A disk process or replace.
Brake Pads do not depart from a brake disk, the wheel is hardly turned by hand
- Corrosion in cylinders of brake supports. Repair a support, probably replace.
Non-uniform deterioration колодок
- Are established Pads inappropriate type. Replace Pads. Address to section Acquisition of spare parts.
- The support is polluted. Clear support mine.
- Heavy piston stroke. Eliminate.
- Brake system негерметична. Check up tightness of brake system.
Klinoobraznyj deterioration brake колодок
- The brake disk rotates not in parallel a support. Check up surfaces прилегания a support.
- Corrosion in supports. Eliminate pollution.
- The piston works incorrectly. Check up piston position.
Scratch of brakes
- Often reason in atmospheric influence (humidity of air). If the scratch appears after long parking at the raised humidity and then vanishes, anything it is not necessary to do.
- Are established Pads inappropriate type. Replace Pads, cover basis plates противоскрипной with paste. Address to section Acquisition of spare parts.
- The brake disk rotates not in parallel a support. Check up surfaces прилегания a brake support.
- The support mine is polluted. Clear support mine.
- Погнуты fastening springs колодок. Replace fastening springs.
- Press springs are stretched. Replace press springs.
Pulsation of a pedal of a brake
- ABS in operation. Normally, the help is not required.
- Too big lateral palpation or the admission on a thickness of a brake disk. Check up palpation and a thickness. Process or replace a disk.
- The brake disk rotates not in parallel a support. Check up a surface прилегания a support.
Control lamp ABS lights up during movement
- Too a food low voltage (more low 10). Check up pressure. Check up, whether the control lamp of the generator after engine start dies away. If everything is all right, check up клиновой a belt of a drive of the generator.
- Damage ABS. Check up reliability of contact and presence of corrosion of joining of weight at the returnable pump (in the hydraulic block).
Suspension bracket and steering
The car withdraws at movement in one of the parties
- Tyres are pumped non-uniformly up.
- Defect of tyres takes place.
- Suspension bracket or steering components (the Head the Suspension bracket and a steering) are worn excessively out.
- Carrying out of adjustment of corners of installation of forward wheels is required.
- Forward brake mechanisms (the Head Brake system) are taken.
Jerks, дёрганье or vibrations take place
- Balancing of wheels is broken or there was an ovality of disks. Make balancing in шиномонтажной a workshop.
- Bearings of wheels are worn out, ослабло effort of their tightening or adjustment (the Head the Suspension bracket and a steering) is broken.
- Racks-shock-absorbers or other components of a suspension bracket (the Head the Suspension bracket and a steering) are worn out or damaged.
Excessive rocking of the car or “зарывание” his nose on turns takes place or at braking
Too hardly the steering wheel rotates
- Liquid level in the tank of system of hydrostrengthening of a wheel (the Head Current leaving and service) has excessively fallen.
- Tyres are pumped incorrectly up.
- Hinges of a steering drive (the Head the Suspension bracket and a steering) are insufficiently greased.
- Adjustment of corners of installation of forward wheels is broken.
- The hydraulic booster does not develop demanded capacity.
Takes place excessive люфт a steering
The system of hydrostrengthening of a wheel does not develop due effort
- It is worn out or damaged приводной a belt of the pump of the hydraulic booster or adjustment of its tension (the Head Current leaving and service) is broken.
- Liquid level (the Head Current leaving and service) has excessively fallen.
- Passableness of hoses or lines of hydraulic system is broken. Check up, in case of need make replacements.
- Air has got to hydraulic system. Pump over system (the Head Current leaving and service).
Excessive deterioration of protectors (not in one any area) takes place
- Tyres are pumped incorrectly up.
- Balancing of wheels is broken. Address in шиномонтажную a workshop.
- Disks of wheels are damaged. Check up, in case of need make replacement.
- Suspension bracket or steering components (the Head the Suspension bracket and a steering) are worn excessively out.
Excessive deterioration of protectors on external edge takes place
- Tyres are pumped incorrectly up.
- Turns are too sharply made. Reduce speed.
- Adjustment of corners of installation of forward wheels (excessive convergence) is broken. Address in a workshop for carrying out of professional adjustment.
- Will drive or is braided the suspension bracket lever (the Head the Suspension bracket and a steering).
Excessive deterioration of protectors on internal edge takes place
- Tyres are pumped incorrectly up.
- Adjustment of corners of installation of forward wheels (divergence) is broken. Make adjustment in a car-care centre workshop.
- Components of a steering or ослабло their fastening (the Head the Suspension bracket and a steering) are damaged.
Local deterioration of a protector takes place
- Balancing of wheels is broken.
- Are damaged or погнуты disks. Check up, in case of need make replacement.
- Defect of tyres takes place.
Defects of brushes of a screen wiper
Проскальзывание
- Elastic bands are polluted. Clear elastic bands a rigid nylon brush and a solution of a washing-up liquid or spirit.
- Shabby edges of brushes, elastic bands are worn out or broken off. Replace elastic bands.
- The old elastic bands, the cracked surfaces. Replace elastic bands.
In the field of clearing the water rests gather at once in drops
- The windscreen is polluted by varnish polish or oil. Clear a windscreen a pure rag with удалителем greasings, oils, силиконов.
The brush clears односторонне - in one party well, in another is not present
- The elastic band is deformed in one party “does not overturn any more”. Establish a new elastic band.
- The screen wiper lever is braided, the brush not precisely adjoins to glass. Cautiously turn the lever, vertical position will not be reached yet.
Crude surfaces
- The elastic band was pulled out from a frame. Cautiously insert an elastic band into a frame.
- The brush adjoins to glass non-uniformly as spring laths or plates are bent. Replace a brush. This malfunction, first of all appears at negligent installation of a spare brush.
- Force of pressing by the lever is too small. Slightly grease hinges of levers of a screen wiper and a spring or establish the new lever.
Defects of tyres
Strong deterioration of the tyre on both parties of a working surface
- Too low pressure in tyres.
Strong deterioration of the tyre in the middle of a working surface, on all circle
- Too a high pressure in tyres.
Non-uniform deterioration of a protector
- Static and dynamic disbalance of a wheel. Probably too big lateral palpation of a disk, too big люфт in bearing hinges.
Non-uniform deterioration in the middle of a protector
- Static disbalance of a wheel. The consequence of strong vertical palpation is possible.
Strong deterioration of separate places in the middle of a working surface
- Blocking traces at full braking.
Sawtooth deterioration of a protector. Often together with rupture of a fabric basis which is not visible outside
- Car overload. Check up an internal part of the tyre on basis ruptures.
Rubber uvulas at lateral edges of a protector
- Wrong adjustment of corners of installation of wheels. The tyre is worn out. Check up also a condition of racks-shock-absorbers.
Formation of agnails on one party of a protector of a forward wheel
- Wrong adjustment of a convergence. The tyre is worn out. Frequent movement on wavy surfaces. Fast movement on turns.
Cord ruptures. At first are visible only from within
- Moving through sharp stones, blows of tyres, etc. on high speed.
Односторонне the worn out working surface
- Check up disorder adjustment.
- Damage ABS. Check up reliability of contact of connection with the case at the returnable pump (in the hydraulics block).
|
home
|