Audi A4, S4

Since 2000 of release

Repair and car operation



Audi A4, S4
+ Introduction
+ Controls and receptions of safe operation
+ Current leaving and service
+ The engine
+ Systems of cooling, heating and the air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual box of a gear change
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
- Body
   The general data and security measures at carrying out кузовных works
   Cleaning and leaving
   Repair of insignificant damages кузовных panels
   Repair of considerable damages of a body
   + The external equipment
   - The salon equipment
      Remarks on work with the salon and security measure equipment
      Removal and installation of spring clips
      Removal and installation of the central console
      Removal and installation of the holder of drinks
      Removal and installation of facing of the lever of a lay brake
      Removal and installation of a cover of the lever of switching of transfers/selectors
      Removal and ashtray installation
      Removal and installation of the central armrest
      Removal and installation of an internal mirror
      Removal and cover installation on a control panel
      Removal and pocket installation from outside the driver
      Removal and installation of a ware box
      Removal and installation противосолнечного a peak
      Removal and installation of facing of a rack And
      Removal and installation of the top facing of a rack In
      Removal and installation of the bottom facing of a rack In
      Removal and installation of a forward overlay of a threshold
      Removal and installation of facings (Sedan)
      Removal and installation of facings (Versatile person)
      Removal and installation of a forward seat
      Removal and installation of a back seat
      Removal and installation of a forward seat belt
      Removal and installation of a back seat belt
+ Onboard electric equipment






Removal and installation of a cover of the lever of switching of transfers/selectors

Manual a check point

Removal

 PERFORMANCE ORDER

  1. Open an ashtray. Strongly pull upwards a cover of the lever of switching (2) together with a cover (6), having disconnected from four clips.
  1. Remove a cover (6) upwards. Turn counter-clockwise a nut (5) and remove the handle (4) from the lever.

Depending on model instead of a nut there can be a collar. (1) – a selector cover.

  1. Press laths and disconnect a cover from a framework (3).

Installation

 PERFORMANCE ORDER

  1. Installation is carried out in sequence, return to removal. Thus put on a cover the lever of switching (arrow) turn a nut (5) clockwise (marksman).

Automatic transmission

Removal

 PERFORMANCE ORDER

  1. Establish the selector in position «D».
  1. Turn the plug (1) counter-clockwise and shift down to an emphasis.
  1. Cautiously pull a stopper (2) of the handle (3) so that the cable collar could be advanced through a backlash between a stopper and the handle.

Do not extend a stopper far since otherwise it is possible to damage the selector.

  1. Close a collar round a clamp (marksman), tighten it and keep in such position.
  2. Remove the handle (3) upwards from the selector.
  3. Open a forward ashtray and disconnect a cover.
  1. Release clips (2) and take out upwards an overlay of the selector (1) of the central console.
  1. Disunite a socket from outside overlays.

For switch Tiptronic removal press inside stoppers (2), disconnect an overlay from the bottom part and take out the switch from an overlay.

  1. Disconnect strong jerk a cover of the selector (1) of the holder of a clip and pull upwards.

Installation

 PERFORMANCE ORDER

  1. Establish the selector in position «D», establish a cover of the selector and fix it.
  2. Join a socket, establish and fix an overlay of the selector and a cover.
  3. Establish into place an ashtray cover.
  4. Establish on the selector the handle and fix it.

The clamp should be thus extended from the handle as it is described at removal, and is fixed by a cable collar. The clamp should show to the left towards the driver.

  1. Remove a collar of a cable and press a clamp into the handle.
  2. Shift the plug on the selector upwards, turn clockwise and fix.


home