Audi A4, S4
+ Introduction
+ Controls and receptions of safe operation
- Current leaving and service
Specifications
The indicator of term of approach of maintenance service
The routine maintenance schedule
The general information on adjustment
Check of levels of liquids, the control of leaks
Check of a condition of tyres and pressure in them. A designation of tyres and disks of wheels. Rotation and replacement of wheels
Replacement of impellent oil and the oil filter
Checks of brake system. Adjustment of a lay brake
Check of fuel system
Check of a condition and replacement of hoses of an impellent compartment, localisation of leaks
Check of a condition of ridge belts of a streaming drive of auxiliary units
Check of functioning of system of cooling and frost resistance of a cooling liquid
Check of a condition of system of release of the fulfilled gases
Check of level of oil of automatic transmission
The visual control of a box of a gear change and the main transfer on leaks, check of level and oil addition
Check of a condition a suspension bracket and steering component
Check of a condition of protective covers of power shafts
Check of level of a liquid of system of hydrostrengthening of a wheel
Check of a central air of air
Greasing of terminators of doors, cylinders of locks, cowl hook, сдвижной panels of the hatch of a roof
The visual control of a seat belt and the block of a pillow of safety
Check of working capacity of headlights and horn
Condition check, adjustment and replacement of brushes of screen wipers
Check of a condition of the battery, care it and gymnastics
Replacement of the battery of emergency supply of system Telematik
Replacement of an element of the filter of air of salon / the coal filter of clearing of air
Replacement of a brake liquid
Check and replacement of spark plugs. Check of a condition of high-voltage wires
Replacement of an element of the air filter of the engine
Replacement of the fuel filter
Check of a condition and tension of a gear belt
+ The engine
+ Systems of cooling, heating and the air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual box of a gear change
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Check of a condition of ridge belts of a streaming drive of auxiliary units Survey
|
|
Deterioration of edges of edges of a ridge belt |
|
|
Cross-section cracks D from an underside of a belt and отслоение edges Е of a ridge belt |
|
|
Разлохмачивание lateral edges F, crack Н and отслоение lateral edges G |
|
|
- It is necessary to check periodically a belt condition, and at detection of defects, to replace a belt.
- The belt tension is carried out automatic натяжителем and check does not require.
- Switch off the engine, establish transmission in neutral position. Lift and establish the car on supports.
- Note a chalk a belt on good a foreground.
- Turn the engine for a pulley of a cranked shaft in a direction of rotation before position at which the cretaceous label is visible. Thus, a site behind a site examine a belt.
- Fingers (and using a small lamp if it is necessary) walk on all length of a belt, feeling on presence of cracks and stratifications. Also check up, whether is not present on a belt of attritions and заполированных to shine of sites. The belt should be examined from both parties that means its necessity перекручивания for check of a condition of a seamy side. Be in passing convinced of absence of a rust, cracks and agnails on pulleys. On a working surface of a belt presence of superficial perpendicular cracks is supposed. If these cracks do not overstep the bounds of one edge and not so deep, to replace a belt there is no necessity.
- The belt tension is checked by strong pressing on it by a thumb and definitions of degree of its deflection. Deflection size measure by a ruler. If the distance centre to centre pulleys makes from 180 to 280 mm the deflection size should equal 6 mm. If the distance centre to centre pulleys is in limits between 300 and 400 mm, the deflection should be 13 mm.
- In the presence of one or several of the specified damages клиновой it is necessarily necessary to replace a belt new.
|
- Correctly place a belt on pulleys — it should be strictly on the pulley centre. Even short-term work of incorrectly established belt can lead to its damage.
|
|
|
|
home
|